斷路器開關動作時間測定器
Circuit Breaker Analyzer & Timer 型號：CAT 100 Series
CAT100 系列繼承了市場領先的 CAT 標準系列的所有功能和經驗。
每台 CAT100 系列設備（3 或 6 個主接點通道）都可使用內置電池供電，可工作長達 8 小時。
CAT100 採用特有的觸控螢幕界面，可大大節省各類中壓和高壓斷路器的測試準備和結果分析時間。通過視覺式的 7" 彩色觸控螢幕，可使CAT100 以獨立設備的形式分析圖形和數字結果。
每台 CAT100 系列設備（3 或 6 個主接點通道）都可使用內置電池供電，可工作長達 8 小時。
CAT100 採用特有的觸控螢幕界面，可大大節省各類中壓和高壓斷路器的測試準備和結果分析時間。通過視覺式的 7" 彩色觸控螢幕，可使CAT100 以獨立設備的形式分析圖形和數字結果。
-
CAT100 系列繼承了市場領先的 CAT 標準系列的所有功能和經驗。
每台 CAT100 系列設備（3 或 6 個主接點通道）都可使用內置電池供電，可工作長達 8 小時。
CAT100 採用特有的觸控螢幕界面，可大大節省各類中壓和高壓斷路器的測試準備和結果分析時間。通過視覺式的 7" 彩色觸控螢幕，可使CAT100 以獨立設備的形式分析圖形和數字結果。
CAT100 系列可以記錄：
- 最多可同時對6 個主接點（每相 2 個斷口）的開關動作時間測量，還包括預插入電阻（如果斷路器中存在）和 4 個輔助觸點。
- 測量預插入電阻（如果斷路器中存在）的電阻值。
- 同時測量兩個線圈電流（跳閘和合閘）。
- 最多可測量四個類比訊號（變電站所內電壓、馬達電壓或任何其它類型的類比訊號）。
- 測量斷路器運動機件的位移、接觸摩擦、超程、回彈、阻尼時間和平均速度。
測試結果以表格和圖形形式列印在 58 mm（2.28 英寸）熱感式列表機（選購配件）上。
-
Main contact inputs
• Number of contact inputs: up to 6(3x2), 2 per phase
• Each channel detects Main and pre-insertion
resistor contacts.- Closed ≤ 10 Ω
- Resistor contacts range 10 Ω to 5 kΩ
- Open ≥ 5 kΩ
Short circuit current 50 mA
• Each channel measures resistance of preinsertion resistorsCoil driver
• Number of channels: 2 (Trip and Close coil)
• Two separate outputs for coil triggering
• Driver characteristics: 300 V DC max, 35 A
DC max
• Electronic drivers provide superior timing
control
• Overcurrent and overvoltage protection
• Coil supply input: 300 V DC max, 35 A DC
maxAuxiliary inputs
• Number of channels: 4, galvanically isolated
• User selectable: dry or wet- Contact sensing (dry):
Open circuit voltage 24 V DC
Short circuit current 5 mA - Voltage sensing (wet):
Working voltage 300 V DC, 250V AC
Low activation mode ± 5V
High activation mode ±10V
Current measurement
• Current measurement for Trip and Close coil,
2 channels, Hall-Effect sensor
• Range ±35 A DC to 5 kHz
• Accuracy: ± (0,5 % rdg + 0,1 % FS)
• Graphic presentation: currents waveform is
displayed with a resolution of 0,1 ms
Analog inputs
• 2 channels – Coil current measurement
• 4 Voltage channels, each channel has four
measurement ranges: ±1 V, ±5 V, ±60 V
and ±300 V AC/DC
The analog inputs are isolated with respect to all
other circuits
Time measurement
Time measurement resolution:
• 0.025 ms for 1 s test duration (sampling rate 40 kHz)
• 0,1 ms for 2 s test duration (sampling rate 10 kHz)
• 1 ms for 20 s test duration (sampling rate 1 kHz)
• 10 ms for 200 s test duration (sampling rate 100 Hz)
Time accuracy: 0,05% of the reading ± resolution
DC output
24 V voltage supply for current clamps
PC Interface
• USB
• Ethernet
Display
• Touch screen color display 7 inch.Breaker operation
• Close (C)
• Open (O)
• Close-Open (C-O)
• Open-Close (O-C)
• Open-Close-Open (O-C-O)
The user can select any desired test sequence
Mains power supply
• Connection according to IEC/EN60320-1;
UL498, CSA 22.2
• Mains supply: 90 V - 264 V AC
• Frequency: 50/60 Hz
• Input power: 250 VAPrinter (optional)
• Thermal printer
• Graphic and numeric printout
• Paper width 58 mm (2.28 in)
• Printer operating temperature:
- 20 ºC - + 70 ºC / - 4 ºF - +158 ºF
Internal battery supply (optional)
• Built-in rechargeable battery
• Li-Ion 14.4 V Cell – 6800 mAh 98 WhTransducer input
• Digital transducer inputs: 1
• Analogue transducer inputs: 1
Applicable standards
• Installation / Overvoltage: Category II
• Pollution: Degree 2
• Safety: LVD 2014/35/EU (CE Conform)
Standard EN 61010-1
• EMC: Directive 2014/30/EU (CE Conform)
Standard EN 61326-1
• CAN/CSA-C22.2 No. 61010-1Time measurement triggers
• External trigger: 2 channels (trigger input
voltage: 10 V – 300 V AC/DC)
• Coil currents: threshold level user selectable
• Auxiliary inputs (change of contacts state)
Dimensions and weight
• Dimensions (W x H x D):
o 503 mm x 406 mm x 193 mm
19.8 in x 15.9 in x 7.6 in
• Weight:
o 8.5 kg / 18.7 lbs.Environmental conditions
• Operating temperature:
- 20 ºC to + 55 ºC / - 4 ºF to + 131 ºF
• Storage & transportation:
- 40 ºC to + 70ºC / - 40 ºF to + 158 ºF
• Humidity 0 % - 95 % relative humidity, noncondensing -
The CAT100 Series inherited all capabilities and experience collected from the market-leading CAT Standard Series.Each CAT100 Series device (3 or 6 timing channels) can be supplied with an internal battery power supply that enables up to 8 hours of operation.CAT100 introduces a unique touchscreen interface designed to significantly save the time required for test preparation and results analysis of all types of medium- and high-voltage circuit breakers. The graphical and numerical results can be analyzed using the standalone CAT100 device via the intuitive 7” color touch-screen display.The CAT100 Series can record:
- Simultaneous timing measurement of up to 6 main contacts (2 breaks per phase) including pre-insertion resistors (if present in the circuit breaker) and four auxiliary contacts.
- Resistance measurement of the pre-insertion resistors (if present in the circuit breaker).
- Simultaneous measurement of two coil currents (Trip & Close).
- Measurement of up to four analog signals (substation battery, motor voltage, or any other type of analog signal).
- Measurement of displacement, contact wipe, over-travel, rebound, damping time, and average velocity of the breaker’s moving parts.
Test results are printed on the 58 mm (2.28 inch) thermal printer (optional accessory) in tabular and graphical form. -
Main contact inputs
• Number of contact inputs: up to 6(3x2), 2 per phase
• Each channel detects Main and pre-insertion
resistor contacts.- Closed ≤ 10 Ω
- Resistor contacts range 10 Ω to 5 kΩ
- Open ≥ 5 kΩ
Short circuit current 50 mA
• Each channel measures resistance of preinsertion resistorsCoil driver
• Number of channels: 2 (Trip and Close coil)
• Two separate outputs for coil triggering
• Driver characteristics: 300 V DC max, 35 A
DC max
• Electronic drivers provide superior timing
control
• Overcurrent and overvoltage protection
• Coil supply input: 300 V DC max, 35 A DC
maxAuxiliary inputs
• Number of channels: 4, galvanically isolated
• User selectable: dry or wet- Contact sensing (dry):
Open circuit voltage 24 V DC
Short circuit current 5 mA - Voltage sensing (wet):
Working voltage 300 V DC, 250V AC
Low activation mode ± 5V
High activation mode ±10V
Current measurement
• Current measurement for Trip and Close coil,
2 channels, Hall-Effect sensor
• Range ±35 A DC to 5 kHz
• Accuracy: ± (0,5 % rdg + 0,1 % FS)
• Graphic presentation: currents waveform is
displayed with a resolution of 0,1 ms
Analog inputs
• 2 channels – Coil current measurement
• 4 Voltage channels, each channel has four
measurement ranges: ±1 V, ±5 V, ±60 V
and ±300 V AC/DC
The analog inputs are isolated with respect to all
other circuits
Time measurement
Time measurement resolution:
• 0.025 ms for 1 s test duration (sampling rate 40 kHz)
• 0,1 ms for 2 s test duration (sampling rate 10 kHz)
• 1 ms for 20 s test duration (sampling rate 1 kHz)
• 10 ms for 200 s test duration (sampling rate 100 Hz)
Time accuracy: 0,05% of the reading ± resolution
DC output
24 V voltage supply for current clamps
PC Interface
• USB
• Ethernet
Display
• Touch screen color display 7 inch.Breaker operation
• Close (C)
• Open (O)
• Close-Open (C-O)
• Open-Close (O-C)
• Open-Close-Open (O-C-O)
The user can select any desired test sequence
Mains power supply
• Connection according to IEC/EN60320-1;
UL498, CSA 22.2
• Mains supply: 90 V - 264 V AC
• Frequency: 50/60 Hz
• Input power: 250 VAPrinter (optional)
• Thermal printer
• Graphic and numeric printout
• Paper width 58 mm (2.28 in)
• Printer operating temperature:
- 20 ºC - + 70 ºC / - 4 ºF - +158 ºF
Internal battery supply (optional)
• Built-in rechargeable battery
• Li-Ion 14.4 V Cell – 6800 mAh 98 WhTransducer input
• Digital transducer inputs: 1
• Analogue transducer inputs: 1
Applicable standards
• Installation / Overvoltage: Category II
• Pollution: Degree 2
• Safety: LVD 2014/35/EU (CE Conform)
Standard EN 61010-1
• EMC: Directive 2014/30/EU (CE Conform)
Standard EN 61326-1
• CAN/CSA-C22.2 No. 61010-1Time measurement triggers
• External trigger: 2 channels (trigger input
voltage: 10 V – 300 V AC/DC)
• Coil currents: threshold level user selectable
• Auxiliary inputs (change of contacts state)
Dimensions and weight
• Dimensions (W x H x D):
o 503 mm x 406 mm x 193 mm
19.8 in x 15.9 in x 7.6 in
• Weight:
o 8.5 kg / 18.7 lbs.Environmental conditions
• Operating temperature:
- 20 ºC to + 55 ºC / - 4 ºF to + 131 ºF
• Storage & transportation:
- 40 ºC to + 70ºC / - 40 ºF to + 158 ºF
• Humidity 0 % - 95 % relative humidity, noncondensing