可攜式開關設備測試系統

可攜式開關設備測試系統
靈活且緊湊的測試系統，適用於中壓、高壓及超高壓開關設備之測試，具有更強的控制與效能。

• 相較於前代機型，提供更多控制輸出與更高主處理單元功率，適用範圍更廣
• 超堅固且緊湊的硬殼設計
• 在單一測試程序中完成完整開關設備測試，無需重新接線
• 可獨立操作
• 7吋觸控螢幕操作與評估
• 最多可測量 12 個接觸室的預插入電阻 (PIR) 與主接點
• 最多可測量 12 個接觸室的靜態與動態接觸電阻
• 可簡易串接額外設備以測試超過 12 個接觸室的開關
• 記錄與分析線圈與馬達電流
• 適用於空氣絕緣與氣體絕緣開關的雙側接地測試

現場完整開關設備測試
透過 ACTAS P260+ | P360+ 內建的控制面板，可於單一測試程序內快速、簡便且靈活地執行並評估完整的開關設備測試。
12 組預插入電阻與主接點測量
可針對最多 12 組預插入電阻與主接點，測定各種開關操作序列的動作時間。
雙側接地
搭配 PROMET SE，可同時對多達 3 極、每極含 4 組主接點的開關進行雙側接地測試；若有更多接觸室亦可擴充。在氣體絕緣開關系統中，可透過電流脈衝測量斷路器單元的操作時間。此時，羅哥斯基線圈 (Rogowski coils) 會安裝於氣體絕緣開關系統的絕緣接地部分。
12 組輔助接點輸入
最多可接收 12 組輔助接點的狀態訊號，內建濕 / 乾接點切換功能。
9 組通用感測器輸入
最多 9 組類比 / 數位感測器輸入，可用於壓力、位移、電流及溫度測量，支援類比與增量式感測器。感測器輸入可依需求靈活參數化設定，並可用於特殊測試程序，例如首次動作（First Trip）或透過電壓偵測系統測量。
線圈與馬達電流
最多可測量 3 組閉合線圈與 3 組開啟線圈的電流。可自由選擇測量範圍以獲得極高精度的測量結果。
電驛輸出
最多 2 組電驛輸出，可用於致動器控制。
接觸電阻測定
可與多種 PROMET 電阻測量裝置搭配，同時在 3 極上測定靜態與動態接觸電阻。依據 PROMET 系統型式，可同時在每極的一個或多個接觸室上進行測試。
欠壓釋放與最小釋放電壓
為了能獨立於變電站電壓下測試馬達與線圈，可由高功率 AC/DC 電源 EPOS 或其他支援電源提供電壓。因此比如欠壓釋放與線圈最小釋放電壓測試可在相同條件下重現。



具獨立運行功能的系統解決方案
結合 ACTAS、PROMET、EPOS 的 KoCoS 系統方案，憑藉其豐富功能與高靈活性，具有明顯優勢：

1. 精確分析整個接觸系統與所有致動器
2. 透過 ACTAS 共同操作與資料管理
3. 共通測試計畫以管理所有測試系統並產出一份測試報告
4. 各測試系統皆可獨立運行以達最大靈活性

氣體絕緣中壓開關設備測試
ACTAS P360+ 可透過開關自身的電壓偵測系統的電容測點，最簡便地測量封閉於 SF₆ 氣體中的中壓系統之操作時間。可直接連接至 ACTAS 測試系統的測量輸入端，無需額外測量元件。
首次動作測量
由於具多樣的感測器連接選項，ACTAS 亦可執行首次動作測試。最多可將五個電流夾連接至電流互感器次級側與線圈端。透過外部觸發訊號，ACTAS 測試系統可自動測定第一次開關操作時的切換時間。
堅固可靠，適用於超高壓領域
ACTAS P260+ | P360+ 採用緊湊且堅固的硬殼設計，並採用經驗證的硬體組件，確保在現場進行中、高及超高壓開關設備、隔離開關與接地開關測試時的可靠運作。
觸控螢幕操作與評估
改良的操作概念與更強大的硬體，使操作更簡單、資訊顯示更清晰。介面結構直觀，使用者可快速上手，無需繁複訓練。

1. 7 吋觸控螢幕與圖形化介面
2. 以直觀圖表與圖示顯示測試結果
3. 測試報告可輸出為 PDF 格式
4. 可從個別範本選擇測試設定
5. 以 LED 清楚顯示接點狀態
6. 具 USB 與乙太網路介面，可直接連接電腦 / 網路或其他外接設備

參數設定與結果分析


測試參數設定與結果分析可直接於現場於儀器上完成，或於辦公室透過電腦及 ACTAS 測試軟體進行。測試資料與參數可隨時透過 USB 隨身碟或網路連線匯入 / 匯出。

Portable Switchgear Test Systems
Flexible and compact test systems for the testing of medium-, high- and extra-high voltage switchgear with a plus in control and performance.

• Wider range of applications due to more control outputs and more power of the main processing unit than the predecessor model
• Extremely robust and compact in hard case
• Complete switchgear testing without reconnecting in one test sequence
• Stand-alone operation
• Operation and evaluation via 7” touch screen
• PIR and main contact measurement on up to 12 contact chambers
• Static and dynamic resistance determination on up to 12 contact chambers
• Simple cascading of additional devices for testing of switches with more than 12 contact chambers
• Recording and analysis of coil and motor current
• Testing with earthing on both sides for AIS and GIS

Complete switchgear testing on site
Using the integrated control panel of ACTAS P260+ | P360+, it is possible to carry out and evaluate comprehensive switchgear tests quickly and easily and with a high degree of flexibility within a single test procedure.
Measurement on 12 PIR and main contacts
Determination of operating times for various switching sequences on up to 12 PIR and main contacts.
Earthing on both sides
In combination with PROMET SE, simultaneous tests can be carried out on up to 3 poles, each of which has 4 main contact chambers, with earthing on both sides. More contact chambers are possible. In GIS systems, the operating times of the breaker units are measured via current pulses. For this purpose, Rogowski coils are attached to the insulated ground of the GIS system. 
12 auxiliary contact inputs
Status messages from up to 12 auxiliary contacts with integrated wet / dry switchover.
9 universal sensor inputs
Up to 9 analogue / digital sensor inputs for pressure, displacement, current and temperature measurement for analogue and incremental sensors. The sensor inputs can be flexibly parameterised according to requirements and used for special measurement procedures such as First Trip or measurement via VDS.
Coil and motor current
Coil current measurement on up to 3 closing and 3 opening coils. Freely selectable measuring ranges make it possible to obtain extremely precise measurement results.
Relay outputs
Up to 2 relay outputs for actuator control
Contact resistance determination
The determination of both static and dynamic contact resistance can be carried out simultaneously on 3 poles in combination with the various PROMET resistance measuring devices. Depending on the PROMET system, measurements on one or more contact chambers per pole and switch can be tested simultaneously.
Undervoltage release and minimum release voltage
To be able to test motors and coils independently of the station voltage, the supply voltage can be provided by the powerful AC / DC source EPOS or other supported source types. Tests of, for example, the undervoltage releases and the minimum release voltage of coils can thus be carried out reproducibly under always the same conditions

System solution with stand-alone option
The KoCoS system solution with ACTAS, PROMET, EPOS offers clear advantages due to its wide range of functions and high flexibility:

1. Precise analysis of the entire contact system and all actuators
2. Joint operation and data management via ACTAS
3. Common test plan for managing the test systems, one test report
4. Stand-alone operation of each individual test system for maximum flexibility

Testing of gas-insulated medium-voltage switchgear
ACTAS P360+ makes it possible to measure the operating times of a medium-voltage system encapsulated in SF6 gas in the simplest way via the capacitive measuring points of the switch’s own VDS system. The connection is made directly to the measuring inputs of the ACTAS test system without any further measuring components.
First Trip- Measurements
Due to the diverse connection options for sensors, first trip measurements can also be carried out with ACTAS. Up to five current clamps are connected to the secondary side of the current transformers and to the coils for this purpose. Using external trigger signals, the ACTAS test system can fully automatically determine the switching time during the first switching operation.
Robust and reliable, even in the extra-high voltage range
ACTAS P260+ | P360+ feature a compact and robust design in a handy hard case. The use of proven hardware components guarantees reliable operation during on-site testing of medium, high and extra-high voltage switchgear as well as disconnectors and earthing switches.
Operation and evaluation on the touch screen
A further optimized, easy-to-understand operating concept and even more powerful hardware ensure simple operation with optimum display of all information. The clearly structured user interface is self-explanatory and leads the user intuitively and quickly to the goal without extensive training.

1.  7“ touch screen with graphical user interface
2. Display of measurement results with easy-to-understand graphics and icons
3. Test report in PDF format
4. Selection of test settings from individual templates
5. LEDs for easy display of contact status
6. USB and Ethernet interfaces for direct connection to PCs / networks as well as for additional devices

Parameterize and analyze


The parameterization of tests and the analysis of test results can be carried out on site directly on the device or also in the office via a PC and the ACTAS test software. The test data and parameters can be imported or exported at any time, e.g. via USB flash drive or network connection.